Polaris 2007 Victory Hammer Manuel d'utilisateur

5SAFETYSymbols and Terms Used in the Owner’ s ManualThe following safety signal words and symbols appear throughout the owner’s manual. Your safety an

95MAINTENANCERear SuspensionInspectRear Shock Absorber Preload (Ride Height )2. The uppermost spanner nut on the shock is the locknut (1). Thespanner

96MAINTENANCERear SuspensionCare should be taken to be sure the motorcycle will not tip or fall while elevated. S evere personalinjury or death may oc

97MAINTENANCEFront Suspension and SteeringCare should be taken to be sure the motorcycle will not tip or fall while elevated. S evere personalinjury o

98MAINTENANCEFront Suspension and SteeringCare should be taken to be sure the motorcycle will not tip or fall while elevated. S evere personalinjury o

99MAINTENANCEFuel SystemCheck Fuel Hose, Rail, and Conn ectio n sInspect the fuel hoses for cracks or damage. Inspect the hose connection at the fuel

100MAINTENANCEFuel SystemFuel can damage painted surfaces and plastic parts. W ipe spilled fuel immediately from the motorcycleusing a clean, dry, sof

AFast IdlePositionFast IdleLeverRestPositionB101MAINTENANCEFast Idle Lever and Cable1. Movefast idle lever. It should move smoothly from restposition

102MAINTENANCEThrottleCheck Throttle Control Grip and Cable1. Rotate the t hrottle control grip. It should rotate smoothly from itsrest position to it

103MAINTENANCEClutchCheck Clutch L ever and Cable1. Squeeze the clutch lever toward the handlebar and release it. Itshould move freely and smoothly an

104MAINTENANCEClutchLubricate Clutch Lever1. Remove right side cover.2. Locate the cable adjuster and loosen the adjuster lock nut (see page 105).3. T

6SAFETYSafe Riding PracticesImproper use of this motorcycle can result in serious injury or death to you, your passenger andothers. To minimize the ri

105MAINTENANCEClutchAdjust Clutch Cable Freeplay1. Remove the right side cover.2. Hold cable (1) and loosen the adjuster lock nut (2).3. Turn cable ad

106MAINTENANCELubricate Control CablesThe following cables used on the motorcycle require periodic lubrication for smooth operation and maximumservice

107MAINTENANCEBrakesCheck Front Brake Lever Mo vementSqueeze the front brake lever toward the handlebar and release it. Itshould move freely and smoot

108MAINTENANCEBrakesCheck Front Brake Fluid L evel1. To check the front brake fluid level, rest the motorcycle on thesidestand and on level ground. Tu

109MAINTENANCEBrakes• Do not operate the front brake while its reservoir cover is removed. Fluid could overflow fromthe reservoir and cause air to ent

110MAINTENANCEBrakesAdjust Rear Brake Pedal Freeplay1. Loosen the brake linkage rod locknut.2. Turn the linkage rod in or out as necessary.3. Tighten

111MAINTENANCEBrakesAdd Rear Brake Fluid1. Bring the motorcycle to a vertical position with an appropriatemotorcycle lift or a block of wood or steel

112MAINTENANCEBrakes• Do not operate the rear brake while its reservoir cover is removed. Fluid could overflow fromthe reservoir and cause air to ente

113MAINTENANCEBrakesCheck Brake PadsLook at the front brake caliper pads at (1), and at rear rear brakecaliper pads at (2). You should see at least 1/

114MAINTENANCEGear Shift PedalAdjust Gear Shift Pedal Height1. Loosen the gear shift linkage rod locknuts.2. Turn the linkage rod in or out as necessa

7SAFETYSafe Riding PracticesThe following design characteristics affect how you should ride the VICTORY motorcycle:S The motorcycle is designed for on

115MAINTENANCETiresCheck Tire PressureNormal riding warms the tires and increases the tire air pressure. For an accurate reading, check the tire press

116MAINTENANCETiresCheck Tire ConditionInspect the tire sidewalls, road contact surface, and tread base for cuts, punctures, and cracking. Replace dam

117MAINTENANCECheck WheelsInspect both wheels for cracks or damage. If you see wheeldamage or cracks, contact an authorized VICTORY dealer tohave the

118MAINTENANCECheck or Replace Spark PlugsThe spark plugs must be removed from the engine to inspect them. Sparkplugs with bright white deposits, soot

119MAINTENANCECheck or Replace Spark Plugs4. Remove the spark plug from the cylinder head with a 5/8 inch sparkplug socket.Both spark plugs should hav

120MAINTENANCECheck Engine CompressionAn accurate periodic engine compression check documents engine wear and condition. For engine compressioncheck p

121MAINTENANCESeat Removal and InstallationThe seat mounting screws are located under the three cowl grommets at the rear of the seat and are accessed

122MAINTENANCEBatteryThe battery contains sulfuric acid, which can cause severe burns. Do not allow sulfuric acid tocontact skin, eyes, or clothing.An

123MAINTENANCEBatteryBattery Removal1. Remove the seat (page 121) and l eft side cover.2. Remove battery cover retaining nuts, and remove the cover(A)

124MAINTENANCEBatteryBattery ChargingThe battery may contain explosive gases.• Keep sparks, cigarettes, or any flame away from the battery.• Shield ey

8SAFETYSafe Riding PracticesFollow these general safe riding practices:S Before each ride, make the checks described in the Pre-Operation Check sectio

125MAINTENANCEBatteryBattery In stallatio n1. Before installing the battery, make sure it’s fully charged andclean.2. Slide the battery into position

126MAINTENANCEFusesUse only recommended amperage fuses to avoid damage to the electrical system.Caution1. Remove right side cover and release fuse box

127MAINTENANCEHeadlamp AdjustmentThe headlamp should shine straight ahead of themotorcycle. The top of headlamp high beam shouldbe just below the cent

128MAINTENANCESidestandStraddle the motorcycle and bring it to a vertical position. Move the sidestand to its stored (up) position, then to itsfully e

129MAINTENANCESidestandSidestand Lubrication1. Bring the motorcycle to a vertical position with an appropriate motorcycle lift or a block of wood or s

130MAINTENANCECheck FastenersVisually inspect the entire m otorcycle chassis and engine for loose, damaged, or missing fasteners. Tighten loosefastene

131MAINTENANCENOTES:

132CLEANINGThis section explains how to properly clean the various parts of your VICTORY motorcycle to keep it in goodworking order and appearance.Gen

133CLEANINGWashing and Drying the MotorcycleBefore washing the motorcycle, make sure the exhaust pipes are not hot. Cover each exhaust pipe opening wi

134CLEANINGWashing and Drying the MotorcycleUse as little water as possible when washing near the air cleaner or the exhaust pipe openings. Anexcessiv

9SAFETYSafe Riding PracticesS The most common cause of accidents involving a motorcycle and an automobile is the automobile driver’s failureto see the

135CLEANINGWaxing, Polishing and Applying Protectants(Items Other Than Windshields and Leather Saddlebags)After washing and drying the motorcycle, you

136CLEANINGWindshield CareIf your motorcycle is equipped with an optional windshield:Wash the windshield using a soft cloth or sponge soaked in a solu

137CLEANINGLeather Saddlebag CareIf your motorcycle is equipped with optional leather saddlebags:Natural leather has “character. ” Each piece used in

138STORAGEIf you will not operate the m otorcycle for several months, such as during the winter, store the motorcycle to preventdamage to the fuel sys

139STORAGEFuel Stabilizer1. Using a mixture of fuel and the recommended amount of VICTORY Premium Carbon Clean Pl us or othergasoline stabilizer, fill

140STORAGETire InflationInflate the tires to normal pressure (see page 115).Battery Care1. Remove the battery (see page 123).2. To clean oxidation fro

141STORAGERemoval from Storage1. Remove the cover and unlock the front forks (if locked with accessory lock).2. Check the tire pressure (page 115) and

142WARRANTIESMotorcycle Noise RegulationTampering with noise control systems is prohibited. Federal law prohibits the following acts or causing thereo

143WARRANTIESEmissions Control System WarrantyVICTORY Motorcycles, Polaris Sales Inc. - Emission Control System Warranty StatementYour Warranty Rights

144WARRANTIESOwner ’s Warranty ResponsibilitiesAs the motorcycle owner, you are responsible for the performance of the required maintenance listed in

10SAFETYSafe Riding PracticesS Reduce your speed when:- The weather is windy, rainy or otherwise causing slippery or rapidly changing conditions.- The

145WARRANTIESI. CoverageWarranty defects shall be remedied during customary business hours at any authorized VICTORY motorcycle dealer located within

146WARRANTIESII. LimitationsThis Emission Control System warranty shall not cover any of the following:A. Repair or replacement required as a result o

147WARRANTIESIII. Limited LiabilityA. The liability of VICTORY under this Emission Control System Warranty is limited solely to the remedying of defec

148WARRANTIESIV. Legal RightsTHIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARYFROM STATE TO STATE.V. This W

149WARRANTIESVICTORY Motorcycle Warranty PolicyLimited WarrantyVICTORY Motorcycle Division, Polaris Sales Inc., P.O. Box 47700, Medina, Minnesota 5534

150WARRANTIESWarranty Coverage And Exclusions:Limitations Of Warranties And RemediesThe warranty excludes any failures that are not caused by a defect

151WARRANTIESALL IMPLIED WARRANTIES (INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY ANDFITNESS FOR A PARTICULAR PURPOSE) ARE L

152SPECIFICATIONSModel Year 2007 HAMMERDimensionsOverall Length 92.7 in (235.5 cm)Overall Width 38.75 in. (98.4cm)Overall Height 47.25 in (120.0 cm)Se

153SPECIFICATIONSModel Year 2007 HAMMEREngineEngine Type Freedom®100 / 6 V--TwinConfiguration 50_ V-Twin4StrokeDisplacement 100 cu in (1634 cc)Cooling

154SPECIFICATIONSModel Year 2007 HAMMERDrive SystemFinal Drive Type Carbon Fiber Reinforced BeltTransmission Type 6 speed Overdrive - Constant MeshPri

11SAFETYSafe Riding PracticesS Ground clearance is reduced when the motorcycle leans. Do not allow components to contact the road surfacewhen leaning

155SPECIFICATIONSModel Year 2007 HAMMERWheels and TiresFront Wheel Type/Size Cast or Billet -- 18 x 3.0″Rear Wheel Type Size Cast or Billet -- 18 x 8.

156SPECIFICATIONSFuel SpecificationsUse only unleaded gasoline, 92 pump octane minimum.DO NOT USE GASOLINE CONTAINING METHANOL.Using gasoline/methanol

157IDENTIFICATION NUMBERSRecord important numbers below.Vehicle Identification Number: ________________________________________(Located on right side

158INDEXAAccelerating 70...Accessory, Battery Charger 124...Accessory Selection and Installation 18..AdjustmentClutch Lever Free

159INDEXEElectrical Equipment 48-49...Emergency Flasher Switch 42...Emergency Flashers 49...Emissions Control System Warrant

160INDEXIIdentification Numbers 157...Ignition Key 35...Ignition Key Number 34...Ignition Switch 35...

161INDEXRRear Shock Absorber Ride HeightAdjustment 94...Measurement 93-95...Rear Shock Absorber PreloadSpecification 93...

162INDEXTTachometer 36...Taillight / Brake Light 48...Test Drive 130...Throttle 102...

12SAFETYSafe Riding PracticesProtective ApparelTo decrease the risk of injury and increase riding comfort, wear protective riding apparel.S Wear a Dep

13SAFETYGross Vehicle Weight Rating (GVWR)Gross vehicle weight is the total combined weight of the motorcycle, the operator and the passenger. **S The

14SAFETYExample 1: HAMMER with n o accessories o r cargoGross Vehicle Weight Ratin g 1165 lbs ( 528 kg)Item WeightHAMMER- with full capacity of all fl

15SAFETYCarrying CargoUse the following guidelines when attaching cargo or accessories to the motorcycle. Where applicable, theseguidelines also refer

16SAFETYSaddlebagsWhen operating a motorcycle with original equipment or accessory saddlebags:S Never ride at speeds exceeding 80 mph (120 km/h). Depe

17SAFETYTransporting the MotorcycleIf you must transport the motorcycle:S Use a truck or trailer. Do not tow the motorcycle with another vehicle, as t

18SAFETYAccessory Selection and InstallationBecause VICTORY cannot test and make specific recommendations concerning every accessory or combination of

19SAFETYGasoline and ExhaustFor complete fueling procedures, see page 64.Gasoline is highly flammable and can be explosive in certain conditions. Obse

20SAFETYMaintenanceMaintain the motorcycle according to the following requirements:S Before each ride, complete a pre-operation check as outlined begi

21SAFETYMaintenanceS Keep the motorcycle clean. In addition to extending the service life and the original appearance of the motor-cycle, a complete a

BDCAE22SAFETYLocation of Safety and Vehicle Information LabelsSee page 23 for decal type and description.

23SAFETYLocation of Safety and Vehicle Information LabelsLocation A (FUEL WARNING)Location B (MANUFACTURING INFORMATION)Information varies by modelLoc

24SAFETYLocation of Safe ty and Vehicle Inform a tion LabelsSee page 25 for decal type and description.F

This product contains or emitschemicals known to the state ofCalifornia to cause cancer and birthdefects or other reproductive harm.California Proposi

25SAFETYLocation of Safety and Vehicle Information LabelsLocation FFUSE and RELAY LOCATION(Under side cover, on side of fuse box cover)FUSE BOX REMOVA

26SAFETYLocation of Safety and Vehicle Information LabelsSee page 27 for decal type and description.HG

27SAFETYLocation of Safe ty and Vehicle Inform a tion LabelsLocation G (TIRE SAFETY)Location H (EMISSION CONTROL INFORMATION)(Canada Models)(49 State

28SAFETYReporting Safety DefectsIf you believe that your vehicle has a defect that could result in a crash or cause injury or death, you shouldimmedia

29SAFETYNOTES:

30COMPONENT IDENTIFICATIONUse the information on the following pages to identify and locate the major components of the VICTORYHAMMER motorcycle, incl

31COMPONENT IDENTIFICATIONLEFT SIDE VIEW1. Front Fork2. Front Turn Signal3. Headlamp4. Air Filter5. Spark Plug (2)6. Ignition Switch7. Left Side Cover

32COMPONENT IDENTIFICATIONRIGHT SIDE VIEW1. Drive Belt (under guard)2. Passenger Seat / Cowl3. Seat Strap (Under Seat Cowl)4. Operator’s Seat5. Rear S

33COMPONENT IDENTIFICATIONVehicle Identification NumberThe vehicle identification number (VIN) is stamped into the front of the steering head and also

34COMPONENT IDENTIFICATIONEngine Identification NumberThe engine identification number (A) is a combination of the enginemodel and serial numbers. The

We’ve created a web site just for YOU!S Technical tipsS New product introductionsS Event schedulesS Parts and Service Manual informationS Exciting det

35INSTRUMENTS, FEATURES AND CONTROLSIgnition KeyThe ignition key operates the ignition switch and parking lights.Ignition SwitchThe ignition switch en

36INSTRUMENTS, FEATURES AND CONTROLSInstrument ClusterThe instrument cluster includes the speedometer and tachometer.1. Speedometer2. Tachometer3. Odo

37INSTRUMENTS, FEATURES AND CONTROLSOdometerThe odometer display shows total miles traveled in the window on the lower portion of the speedometer.Trip

38INSTRUMENTS, FEATURES AND CONTROLSIndicator LightsNeutral Indicator (1)The neutral indicator illuminates when the transmission isin neutral, and the

39INSTRUMENTS, FEATURES AND CONTROLSLow Oil Pressure Ind icato r (4)The low oil pressure indicator illuminates when engine oil pressure drops below sa

40INSTRUMENTS, FEATURES AND CONTROLSLeft Handlebar ControlsFast Idle Lever (1)The fast idle lever increases the engine idle speed when starting acold

41INSTRUMENTS, FEATURES AND CONTROLSLeft Handlebar ControlsTu rn Signal Switch Op eration (3)With the ignition key in the ON or PARK position, the tur

42INSTRUMENTS, FEATURES AND CONTROLSRight Handlebar ControlsEngine Stop/Run Switch (1)The engine stop/run switch completes or interrupts the ignition,

43INSTRUMENTS, FEATURES AND CONTROLSRight Handlebar ControlsStarter Button (3)The starter button works only when the engine stop/run switch is in the

44INSTRUMENTS, FEATURES AND CONTROLSGear Shift Pedal (1)The gear shift pedal is located on the left side of the motorcycle. Toshift to a lower gear, p

45INSTRUMENTS, FEATURES AND CONTROLSFuel CapThe fuel cap must be opened and closed with the ignition key.To open:DLift key slot c over (1) on cap and

46INSTRUMENTS, FEATURES AND CONTROLSSide CoversYour motorcycle is equipped with two removable side covers.Remove the left side cover to access the bat

47PRE-OPERATION CHECKTo keep your VICTORY motorcycle in good operating condition, always perform the checks described in thissection before each ride.

48PRE-OPERATION CHECKCheck Electrical EquipmentTo perform a pre-operation check on the electrical equipment, set the ignition switch to t he ON positi

49PRE-OPERATION CHECKCheck Electrical EquipmentTurn SignalsMove the turn signal switch to the left. The front and rear left turn signals and the turn

50PRE-OPERATION CHECKCheck Engine Oil LevelA dipstick attached to the oil fill cap registers the engine oil level.We recommend the use of only VICTORY

51PRE-OPERATION CHECKCheck Fuel ComponentsFuel Level1. Straddle the motorcycle on level ground and bring it to a vertical position.2. Turn the ignitio

52PRE-OPERATION CHECKCheck T iresTire PressureNormal riding warms the tires and increases the tire air pressure. For an accurate reading, check the ti

53PRE-OPERATION CHECKCheck BrakesFront Brake L ever MovementSqueeze the front brake lever toward the handlebar and release it.It should move freely an

54PRE-OPERATION CHECKCheck BrakesRear Brake Pedal Freeplay and MovementRear brake pedal freeplay, the amount of brake pedal movementfrom the rest posi

1The text, photographs and illustrations used in this manual are based on the most current product informationavailable at the time of publication. Pr

55PRE-OPERATION CHECKCheck Rear Brake Fluid L evel1. To che ck the rear brake fluid level, remove right side cover.Straddle the motorcyc le and bring

56PRE-OPERATION CHECKCheck BrakesCheck Hoses and ConnectionsInspect all brake hoses and connections for dampness or stainsfrom leaking or dried fluid.

57PRE-OPERATION CHECKCheck Clutch1. Squeeze the clutch lever toward the handlebar and release it. Itshould move freely and smoothly and should return

58PRE-OPERATION CHECKCheck Front Suspension1. To check the front suspension, straddle themotorcycle and bring it to a vertical position.2. Apply the f

59PRE-OPERATION CHECKCheck Rear SuspensionProper rear suspension adjustment is essential for a safe and comfortable ride. Check the rear shock absorbe

60PRE-OPERATION CHECKCheck SidestandStraddle t he motorcycle and bring it to a vertical position. Move thesidestand (1) to its stored (up) position, t

61OPERATIONThe operation section describes how to operate your VICTORY motorcycle for best performance and longevity.Important areas covered include:S

62OPERATIONEngine Break-in PeriodDuring the first 500 miles (800 kilometers), critical engine parts require special wear-in procedures so they seat an

63OPERATIONEngine Break-in Period0 -90 miles (0 -145 kilometers)S Do not operate the motorcycle for extended periods of time at throttle positions abo

64OPERATIONEngine Break-in PeriodFueling and Fill HeightFuel the motorcycle with the sidestand down and on level ground. Use only the recommended fuel

2FOREWORDThank you for choosing a VICTORY motorcycle!This owner’s manual contains information for the VICTORY HAMMER model. Some of the photographs an

65OPERATIONEngine Break-in PeriodStarting the EngineThe VICTORY motorcycle has a starter interlock system. The engine can be started only when the tra

66OPERATIONEngine Break-in PeriodStarting the Engine6. Leaving the throttle closed, press and hold the starter button until the engine starts. If the

67OPERATIONShifting GearsThe clutch must be fully disengaged (clutch lever pulled completely in toward the han dlebars)before you attempt to shift gea

68OPERATIONShifting Gears1. To engage first gear, start the engine (see Starting the Engine on page 65).2. W ith the engine at idle speed, engage the

69OPERATIONShifting Gears• Downshifting at a speed in excess of the recommended downshift point may severely damage thetransmission or cause the rear

70OPERATIONAcceleratingTo accelerate, open the throttle (roll the throttle control grip toward you). For even acceleration, open the throttlewith a sm

71OPERATIONBrakingTo slow the motorcycle with the brakes, close the throttle and apply the front and rear brakes evenly. As themotorcycle slows, eithe

72OPERATIONStopping the EngineBefore stopping the engine, bring the motorcycle to a complete stop either in neutral or with the clutch disengaged.Once

73OPERATIONParking the MotorcycleWhen parking the motorcycle, choose a flat, firm surface. Bring the motorcycle to a complete stop and, with thetransm

74OPERATIONParking the MotorcycleAsphalt pavement can become soft in hot weather. The sidestand can sink into soft asphalt until themotorcycle falls o

3TABLE OF CONTENTSINTRODUCTION 4...SAFETY 5...

75MAINTENANCEThis section includes information for maintaining your VICTORY motorcycle. It includes recommended periodicmaintenance intervals, which o

76MAINTENANCEInitial MaintenancePerform the initial maintenance after you’ve ridden your new motorcycle 500 miles (800 kilometers). Thismaintenance is

5000 (8,000)7,500 (12,000)2,500 (4,000)500 (800)10,000 (16,000)12.500 (20,000)15,000 (24,000)17,500 (28,000)20,000 (32,000)22,500 (36,000)25,000 (40,0

5000 (8,000)7,500 (12,000)2,500 (4,000)500 (800)10,000 (16,000)12.500 (20,000)15,000 (24,000)17,500 (28,000)20,000 (32,000)22,500 (36,000)25,000 (40,0

5000 (8,000)7,500 (12,000)2,500 (4,000)500 (800)10,000 (16,000)12.500 (20,000)15,000 (24,000)17,500 (28,000)20,000 (32,000)22,500 (36,000)25,000 (40,0

80MAINTENANCEMAINTENANCE RECORDMAINTENANCE PERFORMED MILES / KM NOTES PERFORMED BY:

81MAINTENANCEMAINTENANCE RECORDMAINTENANCE PERFORMED MILES / KM NOTES PERFORMED BY:

82MAINTENANCEEngine OilChange Engin e Oil and Oil Filter (Oil Change Kit PN 2873551)A hot engine or hot exhaust pipes can be hazardous. The engine and

83MAINTENANCEEngine OilChange Engine Oil and Oil Filter8. Make sure the new oil filter gasket is properly seated in the oil filter, and apply a thin f

84MAINTENANCEEngine OilCheck Engine Oil Level1. With the transmission in neutral, start and run the engine for severalminutes.2. Shut the engine off a

4INTRODUCTIONRead the Owner’s ManualYour VICTORY owner’s manual contains information that’s essential to safe riding and proper maintenance of themoto

85MAINTENANCEInspect Air FilterThe standard VICTORY air filter element is a dry, treated paper designand does not require the use of air filter oil.No

86MAINTENANCEDrive B eltCheck Drive Belt ConditionReplace the drive belt if it is cracked or has broken teeth or frayed edges. No matter its condition

87MAINTENANCEDrive B eltCheck Drive Belt Tension (Cont.)2. Position the small O-ring on the belt tension gauge directly overthe 10 lbs. mark on the pl

88‘MAINTENANCEDrive B eltAdjust Drive Belt TensionCare should be taken to be sure the motorcycle will not tip or fall while elevated. S evere personal

89MAINTENANCERear WheelAlignmentA skewed rear axle can damage the d rive belt, causing it to fail and loss of control of the motorcycle.WARNING1. Brin

90MAINTENANCERear WheelAlignment (cont.)NOTE: Turn the axle adjusters about 1/16 of a turn at a time and monitor wheel alignment as you proceed.5. On

91MAINTENANCERear WheelAlignment (cont.)8. Recheck drive belt tension and alignment to be sure it is correct after tightening the axle.9. If alignment

92MAINTENANCERear SuspensionInspect Rear Shock Absorber Pre -Load (Ride Height)This procedure involves using the shock absorber preloadwrench PV-43507

93MAINTENANCERear SuspensionInspectRear Shock Absorber Preload (Ride Height )Measure from floor to rearmost flatsection of right side frame cradle.Spe

94MAINTENANCERear SuspensionAdjust Rear Shock Absorber Preload (Ride Height)1. To adjust the shock absorber spring pre-load:1. Rest the motorcycle on